We've discovered this post on A Step-by-Step Guide to Installing a Bathtub below on the internet and thought it made good sense to discuss it with you here.
Installing a bathtub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately challenging task. If the old bathtub is conveniently obtainable, the job can move easily; if you need to open a wall surface to remove the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is better to think about employing one before you start. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you mount a new bath tub in your restroom if you have actually already purchased a brand-new tub as well as do not need to alter the setup of your previous supply of water pipes.
Your devices and also product checklist ought to make up the following:
- New Tub
- Hammer
- Pipeline Wrenches
- Prybar
- Shatterproof glass
- Degree
- Pliers
- Adjustable Wrench
- Putty Knife
- Screwdriver
- Cold Blade
- Measuring tape
- Pipeline Caps
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome because of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines are in location between the tap as well as the sink. Safeguard the faucet in position with the supplier offered backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap adapters. The former type must be linked to the tap finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Using both wooden boards under its feet, place the bathtub in the needed position. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 little points.
The following objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bathtub until the level reads level.
To mount taps, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Turn on the water as well as examine all joints and brand-new pipework for leaks and also tighten them if required. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has been utilized at the very least once as this will settle it right into its last position.
Getting ready for the Installment
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last setting.
Tiling Around the Tub
In the area where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack a stiff seal, triggering the water to penetrate the wall surface in between the bath and the tiling, leading to difficulties with moisture as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can break fairly very early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is advisable to fit the floor tiles using waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader about How to Install a Bathtub, I assumed sharing that piece of writing was appropriate. Loved our entry? Please share it. Let other people check it out. I cherish reading our article about Installing A Bathtub.
Free Estimate
Comments on “Can I Set Up A Tub Myself?”